![]() ![]() I had them out and decided to look in and here's what I found, the fog light plug. I originally found I was pre-wired for fogs when I was swapping out my turn signals. ![]() Tucked up in there should be the switch connection pictured below. In the area where the switch blanks are on the panel you will see an opening in the dash. Take the panel under the steering wheel off. If you see electrical connections your good to go. If standing at the tire, the relay will be on the lower right hand corner and the 15A fuse is labeled on the cover also. This concludes your installation and should have you all wired up! Let us know if you have any questions or comments below.For those of you that do not have factory fog lights and want some, the process can be very simple, if your pre-wired of course! First off check if your pre-wired for fog's by looking in the front passenger side fuse box. Make sure the cover does not pinch any wires when installed. Connect the brown (ground) wire from the relay harness to the negative battery terminal.Secure the wire to the main battery cable with tie wraps.Place the fuse holder where you can reach it later, should you need to replace the fuse. ![]() ![]() Bolt the red wire with the inline fuse to the positive battery terminal.Push the switch straight into the dash opening until it clicks in place.Install a Euro headlight switch with a fog light switch setting (ES8602).Carefully break this tab off with needle nose pliers or a similar tool. If you want to disable your daytime running lights (DRLs), locate the TFL tab on the back of the light switch.Tug the wire a few times to be sure it won’t pull out. When it is fully inserted, it should click and lock in place. Push the blue wire into terminal 8 of the headlight switch connector. Plug the blue wire into the #8 terminal in the harness connector (arrow).Route and secure the wire so it cannot get caught in pedal mechanisms or the steering column. Secure the wire beneath the dash with zip ties.Route the blue wire up from the underdash area, and pull it through the light switch opening in the dashboard.Squeeze the retainer clips on the wire harness connector and pull the plastic connector out of the switch.If your car has a stock switch with no fog light setting, you’ll need to order one (ES8602). This car already has a Euro headlight switch with fog light setting.Then pull the switch straight out of the dash.Press in on the light switch knob and while turning it clockwise until it stops.Remove the light switch from the dashboard Reach up and pull the blue wire through the grommet into the interior, beneath the dash. Remove the Torx® screws securing the underdash panel, then drop it down. Run the blue wire through the rubber grommet in the firewall, located just above the brake booster. Locate one of the two available grommets in the firewall to route the blue harness wire into the cabin. Run the blue wire through the firewall to the interior. This can be easily removed with a small flat-blade screwdriver or pick. Service Tip: You may need to remove a small green rubber plug from the pin 2 location to make room for the new wire. Push the purple plastic retainer back in place to lock all the wires in the connector, then repeat this step at the other headlight. Insert a yellow harness wire into the pin 2 location of each headlight connector (This will supply power to the fog light through the main OEM connector). Use a small screwdriver or punch to slide the purple plastic terminal retainer (arrow) out of the electrical connector. Route one of the two yellow wires from the relay harness to a headlight connector. Just make sure the power (red) and ground (brown) wires in the relay harness can reach the battery terminals Step 2 Here, we remove the plastic hood cable shield (two screws, top arrows), then drill a hole in the shield to mount the relay.ĭrilling two extra holes let us tie wrap the harness wires to the cover. Mount the fog lamp relay (lower arrow) in the engine compartment near the battery. This instruction manual will take you through the process and help you get on your way to a sharper look and higher visibility. Want to activate the fogs in your MK4 VW? This wiring harness kit will allow you to use a factory set of fogs and wire them into your non-fog light equipped MK4 VW. ![]()
0 Comments
Leave a Reply. |